Parkside PDKS 120 User Manual download pdf (Page 9)

9 GB/IE/CY

suitably qualiﬁed person or at the Customer

Service Centre.

J Always work with the mains lead leading

away from the rear of the device.

J If a dangerous situation arises, pull the mains

plug immediately out of the mains socket.

J Always switch on the electrical power tool before

moving the workpiece against it. Otherwise

there is the risk of kickback.

J Do not cut moist materials or damp surfaces,

J Use only undamaged, defect-free saw blades

7

.

Distorted or blunt saw blades

7

can break or

cause a kickback.

J Ensure that the teeth on the saw blade

7

point

downwards before you mount it in the device.

J DANGER OF INJURY! Keep your hands

away from the area of the saw blade.

J Before sawing, check the workpiece for foreign

bodies such as nails etc. and remove them. In-

jury and / or damage to property may result from

the saw blade striking nails etc. embedded in

the workpiece.

J Always keep the device clean, dry and free

from oil or grease.

J Switch oﬀ the device before you remove any

wood residue from around the saw blade.

Otherwise you could become injured.

WARNING!

HAZARDOUS DUSTS /

VAPOURS! Any noxious dusts or vapours

generated from sawing represent a risk to the

health of the person operating the device and

to anyone near the work area.

J Do not saw materials containing substances

harmful to health.

J Do not use the tool on materials containing

asbestos. Asbestos is a known carcinogen.

J Make sure you have adequate ventilation.

J Wear protective glasses, hearing

protection, dust protection masks

and protective gloves.

Q

Advice on use

J Push the workpiece slowly and with minimum

pressure on to the saw blade.

J Reduce the rate of advance when you are

cutting thicker material.

J Hold the workpiece ﬁrmly on the table with

both hands and push it slowly towards the saw

blade. Otherwise the saw blade may twist or

break.

J Avoid making any sharp changes in direction

during sawing to prevent the saw blade from

twisting or tearing.

J Before starting the saw cut, drill a hole at a

corner or internal cut-out in the workpiece and

start sawing from the hole.

J Use the correct saw blade. The choice of saw

blade depends on the thickness and type of

material and the intended cut.

Select a saw blade with ﬁne teeth to saw thin,

hard materials.

Use a narrow saw blade to saw small radius

cuts.

Q

Assembly

WARNING!

DANGER OF INJURY!

Pull the mains plug out of the socket before you

carry out any task on the device,

Q

Attaching the blade guard

9

(see Fig. A)

j Push the screw

10 c

from the inside through the

slot in the blade guard

9

.

j From the outside of the blade guard

9

, place

the guide plate

10 b

on to the screw

10 c

.

The bent-up side of the guide plate

10 b

engages

around the blade guard

9

.

j Attach the blade guard

9

between the two at-

tachment arms

11

and insert the two screws

10 c

through the openings provided for them in the

attachment arms

11

.

j Ensure that the upwardly curved end of the

blade guard

9

is at the top.

j Put the plain washers

10 a

on from the outside

of the attachment arms

11

.

j Screw the knurled nuts

10

on to the two screw

ends

10 c

.

j Slide the blade guard

9

into the desired posi-

tion and ﬁx it in that position by tightening the

knurled nuts

10

.

Safety advice / Assembly

33383_SCROLL SAW_Dekupiersaege_Content_LB6.indd 9 23.07.09 11:29

1 2 3 4 5 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments