Parkside PABK 60 A1 User Manual download pdf (Page 10)

10 GB/IE/CY

Note: During use of the blow gun

with the

corresponding hose

incl. adapter for the

compressor

2 a

, there is a small discharge ope-

ning on the adapter

2 a

, which releases air. This

serves to create a more uniform airﬂow for ea-

sier and better handling of the blow gun

. This

is not a defect, rather, it serves for better hand-

ling and an improvement of the spray results by

means of a uniform airﬂow.

Mixing paints for use

The paints included are water-soluble. In order to

properly apply the paints, add water and stir. As

delivered, the paints are too viscous.

First ﬁll the beaker with your selected paint

colour with water.

Now screw the cover back on the beaker and

shake it.

Now use the pipette

to remove two drops

of the slightly diluted paint paste and add them

to a paint mixing beaker completely ﬁlled with

water (

Shake the beaker. Now your paint has reached

the correct consistency.

Attach the paint mixing glass (

) accord-

ing to Ill. B.

Note: If desired, you can adjust the amount of

water added to inﬂuence the colour intensity

yourself as with a watercolour box. The more

water you add, the „thinner“ the colour.

You can also mix individualised colour tones

from the available colour pastes. Please take

note, there must be no paint clumps remaining

in the paint containers. The consistency should

correspond to that of water.

Note: If the paint used does not cover well, in-

crease the amount of paint in the mixture ratio.

Turning airbrush compressor

on / oﬀ

Turn the airbrush compressor

on by setting the

on / oﬀ switch

to the position “I“ (see Ill. C).

Turn the airbrush compressor

oﬀ by setting

the on / oﬀ switch

in the position “0“ (see

Ill. C).

Note: Full pressure is built up after two seconds.

Regulating the air pressure

Regulate the air pressure by actuating the vent

of the air blow gun

to more or less of an

extent.

ATTENTION! The device has a pressure switch,

which periodically and automatically turns the de-

vice oﬀ if there is excess pressure or if it is not in use.

Shortly before reaching the switch-oﬀ point, the

compressor runs more roughly and vibrates. This

may also be the case when re-started under load.

The performance and functionality are not impaired

by this. This is not a defect, rather, serves to protect

the compressor from overloading.

Note: The blow pistol

blows air through the

discharge openings even without actuating the trig-

ger. This is NOT A DEFECT.

Through actuating the trigger, the air discharge is

increased so that more air volume ﬂows.

Note: During use of the blow gun

with the cor-

responding hose

incl. adapter for the compres-

sor

2 a

, there is a small discharge opening on the

adapter

2 a

, which releases air. This serves to create

a more uniform airﬂow for easier and better handling

of the blow gun

. This is not a defect, rather, it

serves for better handling and an improvement of

the spray results by means of a uniform airﬂow.

Regulating the spraying results

Regulate the amount of the paint supplied by

turning the paint nozzle of the spray stylus to

the right or left (see Ill. B).

Preparations for use / Cleaning and care

Preparations for use

73868_par_Airbrush_Set_Content_GB-IE-CY.indd 10 06.07.12 12:26

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 36 37

Comments to this Manuals

No comments

Parkside PABK 60 A1 User Manual Page 10

Comments to this Manuals

Related products and manuals for Equipment Parkside PABK 60 A1